Programming the keypad to the opener must be completed within the 30 seconds. Note: The openers LEARN LED will time out in 30 seconds. Press & Release the learn code button once. Place the garage door opener into programming mode:ġ. Note: The learn code buttons are normally located under the lens covers on earlier models. Garage Door Openers manufactured between 1995 to 2011 and all external receivers The round LED will go out and the long LED will begin flashing purple. Press and hold the program button until the round LED turns blue, then release.Ģ. Place the garage door opener into programming mode. All buttons perform the same function and programming is the same for all types shown above. There are 3 types of programming button pads. ![]() Putting the garage door opener into programming mode. See STEP 3 SINGLE DOOR OPERATION for further instruction This completes the programming of a single door.Press the UP/DOWN key 3 to 4 times slowly until the garage door opener operates. Place garage door opener into PROGRAMMING MODE as illustrated below.Ģ. STEP 2A) PROGRAMMING THE KEYPAD TO 1 OPENER- (if you have more than one garage door skip to the next step.)ġ. If LED did not blink twice and shut off, please see RESETTING THE KEYPAD (FACTORY DEFAULT) section.See STEP 2B PROGRAMMING FOR MULTIPLE OPENERS if using the keypad to operate up to 3 doors.The keypad is now programmed with a PIN number and ready to program to the garage door opener(s).Program the keypad for the first time* with a Personal Identification Number (PIN). How to program the Wireless Keypad, Genie garage door openersįor use with Genie Intellicode® garage door openers Wait 15 seconds until the backlighting shuts off before entering a valid PIN or resetting the keypad to reprogram.The Keypad LED, PROGRAM key and Number pad black light will flash rapidly indicating a problem with the programming or invalid PIN entry. The Keypad LED and PROGRAM key will flash slowly and the number pad backlight will remain on for 15 seconds indicating a successful program or valid pin number has been entered. The keypad LED will flash each time a key is pressed and entry is accepted. Reinstall the battery compartment door to begin programming. *It is recommended to complete the programming before mounting the keypad.Īctivate the Genie wireless keypad (GK-R) by opening the battery cover compartment and pull the protective tab. The new DC motors will be different.GK-R (Genie Garage Door Opener Keypad) Programming Quick Reference Card This covers most of the “Intellicode” models. Always check your owner’s manual for your particular model. Other Genie models may require different methods. O Note: Any keypad button will control the door for 30 seconds after the door starts moving. You will now be able to use your wireless keypad normally. O PRESS & RELEASE the UP & DOWN ARROW button 3 times, or until the door begins to operate. Depending on model, the learn code button will be located under the light cover or on the rear panel. O Locate the Learn Code button on your Intellicode/CodeDodger garage door opener. Push the remote button a third time and the door will operate. Push the remote button a second time and the LED light will go out. ![]() ![]() Push and release the button on the remote the LED light should stop blinking and remain solid. O PRESS & RELEASE the learn button, the LED light will blink at a rate of two times per second. All memory has now been erased from the operator. O PRESS & HOLD the learn button on the motor until the LED light goes out. O Voila! You have just reset your keypad. Then enter your four digit code the keypad, then PRESS & HOLD the enter button, the operator will click and the lights flash, PRESS & RELEASE the enter button a second time and the door will operate. O Now PRESS & RELEASE the learn button again. PRESS & RELEASE the button on the remote a second time and the door will operate. O Now PRESS & RELEASE the button you would normally press to open the door – you will hear the motor click and the light will flash. O PRESS & HOLD the learn button on the back of the motor until the LED light goes out. We offer LiftMaster and Genie Garage Door Openers and here are simple instructions to reprogram your keypad and your remotes. When it comes to protecting your home and your family, one can never be too safe. We also suggest that new homeowner’s change their Garage Opener key pad codes as well as reprogram their remotes once they are moved in. Have you recently had service work done in your home and given your Garage keypad code to the service technician? Or maybe your ex-boyfriend had your extra Garage Door opener remote and you are no longer granting him access into your home.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |